0
Add your answer:
Earn +20 pts
How do you replace golf shaft?
Remove the existing one, replace it with a new one.
Can any lacrosse head fit on a stx scti shaft?
Any head will fit on any shaft. But if you but a head on a shaft that is a different brand than the shaft, you may need to drill a new hole into the shaft. The only exceptions are the STX Crankshaft shafts which need certain heads.
What are golf shafts made of?
There are two types of golf shaft- Steel and Graphite. Generally steel is used on irons, wedges and putters, whereas graphite is mainly used for drivers and fairway woods. A new type of shaft has recently evolved it is the bi-matrix shaft which is steel and graphite.
Can you switch a shaft from one golf driver to another golf driver?
Yes, in principle you can take a shaft out of one club and put it in another. If it's a steel shaft, it's almost certainly cheaper to just replace it with a new one. For graphite it's not beyond the capabilities of a well-equipped shop, but it would still probably be cheaper when it was all over to put a new one in the other clubhead. Unless it was a really special shaft. And I can't define "really special".
Can a warrior lacrosse head fit on a Reebok shaft?
well it may depend on the type of stx head or warrior shaft,,, usually they can but you may have to drill a new hole. i had an stx proton power on my warrior krypto pro, and all i had to do was drill a new hole.... hope this helped :)
Can you still use a golf club if the piece connecting the shaft and the head no longer sticks?
If the hosel is broken, it's probably not worth fixing. If the shaft has broken, leaving you with a clubhead with a little bit of shaft down in the hosel, it's not a big deal to re-shaft it. A local golf shop can do it, or you can use it as your excuse to explore the wonderful world of clubmaking. Best case there's enough of the broken shaft sticking out so that you can grab it with vise-grips. Heat the hosel with a propane torch until the epoxy bond fails, then twist the broken piece out. If not, you can use a shaft extractor, which is like a screw extractor (a.k.a. an easy-out to get a grip on the shaft, then heat it with a torch as before. Either way, once you get the hosel cleaned out, re-shaft as usual. You can most definitely drill the excess shaft that is broken off in the hosel if that is the case, then if you want, you CAN make an even cut across the old shaft, as low as possible, and use that shaft to reshaft, but that will result in a club up to 2 inches shorter. Regardless, if you do reshaft, find the strongest epoxy you can, because I have been reshafting clubs for a good while and I have given up on the cheap stuff, it just doesn't cut it. (Especially on irons) Your local pro can and will repair the club if it is worth repairing, but don't bother if it's not worth more than $50-$100. You can reshaft yourself by drilling out the old piece of shaft left in the head or heat the shaft/head up to break the old glue bond and pull. Find a local place that sells heads, shafts, etc of try www.golfsmith.com. They have a wealth of information.
How can you save your game progress on an existing Android phone and transfer it to a new phone?
your stupid head if you dont know
Where can you get a smooth golf ball?
You cannot buy a smooth golf ball, it would not have a consistent flight. If you have plenty of time on your hands you could sand the dimples off a golf ball and see how unpredictable it is. Answer: That was the original golf ball, I don't think if it's still existing. Golf balls have dimples because it has a purpose and not jus a design. If you would know why, then I bet you will like the new one.
How do you put a lacrosse head on a lacrosse stick?
Normally the lacrosse head is screwed into the shaft. You can therefore use a screwdriver to unscrew the screw connecting the head to the shaft. once the screw is removed you will be able to remove the head from the lacrosse shaft
What causes a golf club to rattle?
You may have a piece of debris from the manufacturing process in the head, or the shaft. Or the head could be loose.I recently had the same problem. brand new driver first day. Tapped the shaft to the floor to see if possible whatever was rattling could be seen through the bottom of the grip. Yep, a piece of green plastic, like a o ring the diameter of a pencil but very thin (1/16 "). Removed with needle nose pliers. done.
How do i trim a golf shaft?
For a steel shaft, a tubing cutter is the best way. You get a clean cut perpendicular to the axis. You'll need to have a hardened wheel that can handle the stainless steel. For high production volume shops a cutoff saw with an abrasive wheel is typical.For graphite, a hacksaw with an abrasive blade works well.If you want to know how much to cut off, you can get basic recommendations from whoever sold you the shaft.
Incorporating new information into existing theories is to as modifying existing theories in light of new information is to?
Incorporating new information into existing theories is to assimilation as modifying existing theories in light of new information is to accommodation?
