0
Add your answer:
Earn +20 pts
How do you hang a skateboard on the wall without taking the trucks off and not drilling into it?
Make a shelf with 2 brackets
Can bearings work on any type of skateboard?
nope. The turning of you on the skateboard depends on the bushings, the two soft round things on your trucks. Some people think that loosening the middle helps you turn but then it just makes your tricks really hard to do. Get good trucks so that the bushings are soft and the trucks itself is tight. Get Destructo d2! the best in the industry. 13 years skateboarding
If good 1 is a neutral' what is its marginal rate of substitution for good 2?
Answer is 0. Solution: MRS=delta(x2)/delta(x1) Good 1 is neutral it means that little change in delta(x2) makes infinity change in delta(x1). It means delta(x1)= infinity => MRS=0
How do you put together a skateboard?
You'll need these parts to assemble a skateboard: (1) Deck(board) (2) trucks(axel the wheels attach to) *optinal but reccomended: (2) riser pads(fit between the trucks and deck) (8) 1" bolts w/ nuts to attach the trucks to the deck (4) wheels (8) wheel bearings with (4) bearing spacers (1) sheet of Grip tape ( covers the top of the deak with the no slip sand paper) ~ HELMET AND PADS FOR BEGINNERS !!! ~ - VooDoo 13 -
What are good skateboards?
go 2 local skateshop get their deck and very good trucks and bearings independent trucks, lucky bearings and spitfire wheels
Are scooter bearings the same as skateboard bearings?
Yes, most bearings are the industrial standard of 8mm unless you have special longboard trucks, most notably Bear 1052's or 1045's or Bear Smokeys, these trucks run 10mm but are not very common. If you can take wheels off with the same wrench on both trucks, then they have the same size bearings.
How do you build a skateboard?
You'll need these parts to assemble a skateboard:(1) Deck(board)(2) trucks(axel the wheels attach to)*optinal but reccomended: (2) riser pads(fit between the trucks and deck)(8) 1" bolts w/ nuts to attach the trucks to the deck(4) wheels(8) wheel bearings with (4) bearing spacers(1) sheet of Grip tape ( covers the top of the deak with the no slip sand paper)~ HELMET AND PADS FOR BEGINNERS !!! ~- VooDoo 13 - uU dont need to build one u can just buy one from the store.=0
Is DBX Izzy a good skateboard brand?
yes these are the worst skate baords ever weels are 2 inches thick?
Can you change 3 wheel roking skateboard to 2 wheel roking skateboard?
No way. Its impossible
How wide are skateboard wheels?
it might depend on the size of the skateboard but mine are 2 inches exactly
What parts would you need to make a skateboard?
well if you wanna make one from scratch it would be hard 1.6 or 7 plys of thin wood preferably maple or bamboo 2.a mould or 2 skateboard decks 3.metal to weld trucks 4.metal to weld bearings (this would be hard and is not advised just buy good bearings like reds or cheapshot if u on a budget) 5.just buy a set of good wheels to 6. to make the deck use the wood put wood adhesive on each side glue them together put them in the mould or clamp the 2 decks on the top and bottom and leave overnight cut shape with a jigsaw and drill holes then spray paint design put trucks whells ect. on and skate
What are the release dates for Barkitecture - 2005 Skateboard Doghouse 2-13?
Barkitecture - 2005 Skateboard Doghouse 2-13 was released on: USA: 2 October 2006
