Best Answer

no you cant

User Avatar

Wiki User

โˆ™ 2012-08-14 07:17:16
This answer is:
User Avatar
Study guides
See all Study Guides
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you take grip off a lacrosse shaft?
Write your answer...
Related questions

How do you take off a lacrosse head from a lacrosse stick?

Normally the lacrosse head is screwed into the shaft. You can therefore use a screwdriver to unscrew the screw connecting the head to the shaft. once the screw is removed you will be able to remove the head from the lacrosse shaft

How can you tell what the shaft flex is on Ping eye 2 irons?

Take the grip off. If there is a green mark at the butt end of the shaft the shaft is stiff.

How do you extend a golf club?

You get shaft entensions and cut them to size. Then you take the grip and grip tape off the club. They fit into the current shaft and must be glued in place as shaft extensions must be permanent. You then reprip the club

How do you shorten the shaft length of a golf club?

You take the grip and tape off the club, then you either use a circular saw blade to trim the shaft or use a specialist shaft cutter to take off the desired length. Then just regrip the club as normal.

How do you take the graphic off a lacrosse stick?

If you have an aluminum shaft with graphics ON TOP of the metal, then you can just take a quarter (because it won't scratch the shaft) and work your way around the stick scratching off the graphic. If it is composite, you are out of luck.

How do you install avs grip?

Just like a normal grip. Take the old grip off and clean the shaft. Place the tape on. Add solvent and slide the grip on. Search for other questions on replacing grips for full details.

How do you shorten a golf club shaft?

It is suggested that you get your club pro to do it. To DIY you would remove the grip and grip tape residue, measure how much you want to take off it, mark it, and using a circular saw begin to cut it turning the shaft as you go to get an even cut, then simply put a new grip on.

How do you take a grip off a golf club?

Use a Stanley knife, preferably with a hooked blade to cut the old grip and pull it off in one piece, then peel or scrape the old tape off being careful not to damage the shaft, and then use solvent to remove any residue.

How do you attach new golf club grips?

You firstly need to remove the old grips by cutting off with a Stanley knife and scraping off the old grip tape. You will need to secure the club in a rubber vice clamp. You then get put a piece of grip tape on the end of the shaft with about half an inch overlap, which you then fold together and tuck into the butt end of the shaft, you then spray or pour grip solvent, petrol or white spirit on to the grip and then put plenty in the actual grip (whilst plugging the bottom of the grip with your thumb) shake well then pour the liquid over the grip tape. You line the grip up, and squeeze the end to get it started, then use your thumbs to apply pressure to the grip as you slide it up the shaft without stopping. You then take it out of the vice and stand at address to check the grip is alligned perfectly.

Can you order a high end putter and have it cut to length by another company?

Sure, or you can do it yourself. All you have to do is determine how much shorter you want the putter to be, remove the grip, cut the shaft with a pipe cutter (assuming it's a steel shaft), and replace the grip. Usually, grips are held in place with double sided tape. You need to get some solvent inside the grip and the grip will slide off easily. If that doesn't work, you may have to cut the grip off and replace it with a new one, but grips are fairly inexpensive. When replacing the grip, wrap some double sided tape around the shaft, put a little solvent on it, slide the grip back on and align it with the shaft. The solvent dries and the grip sticks in place. Good luck.

What if your lacrosse head is stuck how to get it off?

hold the top of the lacrosse head to the ground and step on the head, pinching the head to the ground under your foot and pull on the shaft of the stick

How do you put a lacrosse head on a lacrosse stick?

Usually there is a screw and you can screw the head through the hole in the shaft so the head will not come off during the game or when you are poke checking or throwing.

How do you take the center supporter off the front drive shaft?

You have to remove the drive shaft and take to to a machine shop. It has to be pressed off Rob

How to take shaft distributor off?

on a 3.1 at the bottom of the shaft there is a pin you knock it out then push the shaft out the top

How do you take the bearing off the shaft in your swamp cooler?

You usually use a tool called a "puller" for that. It has little claws that grip onto the bearing and a screw that pushes on the shaft. Go talk to someone at your local auto parts store, they may rent them.

How do you take off a crank shaft pulley?

how to get the crank shaft pulley off of a 03 Hyundai elanta GLS

What is the penalty in lacrosse when you take your hand off your stick?


How do you take extra string off a lacrosse stick?

You cut the extra string off

How do you remove an airplane propeller?

you take it off the shaft

If you spraypaint your lacrosse stick shaft will it make it heavy?

It will make it slightly heaver but not much. The paint chip off giving/taking checks from people

How do you take sticky grip off of a hockey stick?

goop remover

Do you have to hold a golf club by the head while in line?

Do you mean when you are waiting to tee off? Then the answer is no, you don't have to but you can do. You can hold it by the shaft, or hold the grip with the head on the ground.

Does the type of lacrosse ball affect how far the ball goes?

Yes. a ball with a worn off grip, also called a "greaser", will not travel as far as a freshly purchased ball. This is why all games are required to use new Lacrosse balls. Balls from different brands such as Warrior or Brine or STX will offer balls with different grip strengths.

How do you extend the length of a golf club?

You need to take the old grip and tape off the golf club, then you cut a shaft extension to size and then with shaft epoxy glue it in place, this is because the rules state that any extension must be fixed. Then let that dry for about 20 minutes or so and then just regrip it as normal.

How do you take off a drive shaft of a 2005 Tahoe?

take the four nuts off connecting it too the rear and pull the curl bolts out and push drive shaft toward the transmission and it should come right out