Best Answer

replacing a blade takes a lot of practice and the right tools so unless you want to bugger up your stick, it would be a good idea to take it to a shop and get it done for a couple bucks(plus the cost of a blade)...if you want to do it on your own you'll need the right glue and a torch. the amount of heat depends if you have a composite shaft or (unlikely) an aluminum one. using the torch keep the flame visible(orange or red or whatever) and roast the end of the shaft like a hotdog. constantly move it right to left while rotating slowly. check every couple of seconds by trying to pull out the blade. once out put some glue in thin strips on all 4 sides of the blade and a little inside the shaft. heat the glue on the blade a little and shove that thing up there

User Avatar

Wiki User

15y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you put the replacement blade on the shaft?
Write your answer...
Still have questions?
magnify glass
Related questions

Put a blade into a tapered shaft?

A replacement blade can be put into a tapered shaft as long as the blade has a tapered hosel. A standard hosel blade will not fit into a tapered shaft. The tapered shaft must also actually be a shaft and not a recently broken one-piece stick. Some players try to cut broken blades off of one-piece sticks and then think they can replace the blade in the remaining shaft. This can work in principle but only at the expense of the natural performance of the stick. It is generally not recommended.

Can a senior replacement blade fit on a junior shaft?

In most situations no it cannot. I would check with who you bought the stick/blade from and ask their opinion.

Will a one55 replacement blade fit into a one70 shaft?

No. The one55 blade is a .620" taper, and the (broken) one70 stick has a .520" taper. A Warrior Dolomite or other tapered blade will fit.

Will a tapered replacement blade fit in a non-tapered shaft?

Sure it'll fit, but it will also come flying out after the first shot you take. Either that or destroy your stick because the tapered blade didn't fit so snugly into your non-tapered shaft.

Can you remove the blade from a 2 piece hockey stick and reuse it?

Yes, the blades are just glued into the shaft. Use a heat gun to melt down the glue, pull out the blade and put it in your new shaft.

Where to get a replacement for broken shaft to blade coupler on lawn mower?

Nobody knows. Buy the new lawn mower. You will save your time and nerves...

Can a 520 hockey blade work with a 620 hockey shaft?

yes but it's complicated to do. you have to put a layer or two of tape inside the shaft and then heat it up and glue it. depending on how much the blade was it may not be worth the hassle.

What shaft can be substituted W54 ping graphite shaft?

You can replace that shaft with any on the market. Since that shaft came with the Ping ISI Irons and had a firm flex, since the W44 were regular, you should get a stiff shaft put in for a replacement.

What is the bottom of the lacrosse stick called?

On the hockey stick, you have the shaft (the part you hold), and the blade (the part that touches the ice). In the blade, you have the Heel, which is the part connected to the shaft. Then you have the toe, which is the tip of the blade, or the end which does not connect to the shaft.

How do you attach a blade to an aluminum hockey stick shaft?

The blade will have glue on it when you purchase it. Heat the end of the blade that goes into the shaft, preferably with a heat gun, until the glue softens.If you dont have a heat gun, you can use a torch. Lightly heat the inside of the shaft as well, and then push the blade down into the shaft, with the butt end of the shaft on the floor. Avoid putting too much heat to the shaft, as it could damage the shaft.

How can you put a replacement blade on a broken s17 easton hockey stick?

You can't at the tapered end (round) of the stick. But at the other end you can put one in.

Can a Bauer shaft hold a Reebok blade?