0
It would be an unlikely event that you have something odd or vary old that may not work. Faucets are standardized so that they can be installed with most any sink that you may be installing or are using.
Wiki User
∙ 16y ago
Wiki User
∙ 13y agoYes. A single hole faucet will either use the center hole for the supply lines and the outside two to hold it down or it is held down in the center also and the other two are for the spout and sprayer with the fourth hole if it is there for a soap dispenser.
Add your answer:
Earn +20 pts
When was Sink the Bismark - song - created?
Sink the Bismark - song - was created in 1960.
Why don't tanks sink on a muddy terrain?
Tanks might be heavy, but their tracks are very wide, spreading that weight over a very large area. Tanks exert less pressure on the ground than a person. But if the ground gets soft enough, even a tank will sink.
Was Justin Timberlake in in-sink?
He was in NSYNC
Has kesha peed in a sink before?
only if...
How do you get scuff marks out of white sink?
Comet, ajax, and soft scrub. Wet sink sprinkle ajax or pour soft scrub, then scrub with abrasive side of sponge.
What kind of faucet is good for stainless steel sink?
Depends on the holes in the ledge of the sink. If you have a single hole, you have to buy a single lever faucet. If you have a two hole or three hole ledge, it depends on the space between them to determine if you need a 4" centre or 8" center faucet
What is the rough in height for a mop sink faucet?
height of a mop sink faucet
How do you install a sink sprayer on a sink that hasn't had one?
That would depend on how many holes the sink has .... If it is a one hole type you will need a pull out spray faucet or look at the Delta line
What side should your kitchen faucet be on a double sink?
As far as I know, all kitchen sinks have the faucet in the middle. There are usually 4 holes, 3 for the faucet and one for the hand sprayer. Some have a fifth hole for a soap dispenser.
What is the standard height of wall mounted faucet over a vessel?
I just had to answer this exact question for one of my plumbers. There should always be about a 1" gap between the top of the sink and the bottom of the faucet. If it is any higher, then the water will splash out of the sink. Also the end of the faucet must go directly over the drain.
Can you convert a single handle kitchen faucet into a double handle faucet?
Change the faucet, either one will mount on the sink.
How do I know what type of kitchen faucet tap I need?
There are many different types of kitchen faucets out there. The kind you need depends on what type of sink you have. It can also depend on personal preference. If you have a low sink, a double sink, three holes, two holes, room for a sprayer, these things will determine what type of kitchen faucet is needed.
Can you drill a hole in a cast iron sink and update to a single handle modern faucet?
Most kitchen cast iron sinks have 3 holes and a single handle uses all three. A bathroom sink will have two or three depending on age and if you are very careful and take your time, you can drill a center hole in cast iron. Start with a small pilot hole in the center from the underneath side. You can't start on top on the porcelain. Once you get the pilot hole through, you can then drill from the top down and should use oil to keep the chipping of the porcelain to a minimum.
Is the water flow the same on a sink faucet and a bath tub faucet?
It depends on the make of the faucets.
What mineral makes a sink faucet'?
steel and iron
Why doe the water not come out of the sink facets but works everywhere else?
if you look under the sink, you will probably see a cutoff valve going up to the sink faucet. turn this on. if that does not fix it, then change you faucet fixture.
Does eljer faucet still honor your lifetime warranty on the sink faucet assembly purchaced in 1995?
They did in 2006.
