0
Add your answer:
Earn +20 pts
What is the Spark plug gap 2003 Yamaha rx1?
.30
What resistance is in the center of your ohmmeter scale Rx1 range?
What resistance is the center of your ohm scales, Rx1 range?
How do you change oil and filter in 2003 Yamaha RX1?
There is a panel on the bottom of the sled. Unscrew the 5 screws with a allen bit. drain the oil from the plug that is there. You also have to take the right panel off the front of the sled and drain the oil out of the oil resevior. To change the oil filter, you have to remove the airbox, then the battery, then the battery frame. The oil filter is under all that. Hope this helps.
How fast does the rx1 mini dirt bike go?
if your very light weight(under 80lbs), then up to 45! anything more and it start to slow down a bit(40_35_30m.p.h.).
How do you test a good and working contactor?
A contactor is tested by using a device called a Multimeter. By setting the multimeter to ohms and rx1 you can clip both prongs to the coil. If the multinmeter moves the contactor is good. If it doesnt move its bad.
What kind of dog is this www dot. i42tinypiccom slash 2cmrx1tjpg?
well this is not a type of dog i don't think but one type of dog that has spots is a dalmatian.www/dot/i41/tiny/pic/com/slash/2cm/rx1/tj/pg
How fast is the fastest ATV in the world?
As of June 2009 In pure stock form, that is right off the showroom floor with NOTHING being added to it, with acceleration and top speed that beats out the best competition, the Polaris Outlaw 525 IRS is the fastest ATV on the market. As far as purpose built machines go : Built by Turbosmart's Puerto Rican Distributor - TurboTech - the "Spiderman" quad uses a turbocharged 1000cc Yamaha RX1 snow mobile engine. Utilising Garrett GT3071R turbo with Turbosmart Ultra-Gate, Race Port BOV, FPR-1200 fuel pressure regulator and an e-Boost2 boost controller, the "Spiderman" quad pumps out 450hp and flies past the 1/8 mile market in just 5.0 seconds! Current Guinness Record holder The highest speed on a quad bike (ATV) is 249.51 km/h (155.04 mph) achieved by Terry Wilmeth (USA) onboard the AlbaAction/Fullbore/Powroll Rocket Raptor version 5.0 at the Madras Airport, Madras, Oregon, USA on 16 June 2007.
What is cross polarization isolation?
Cross polarisation isolation or Cross Polarisation Discrinimation (XPD) is the difference in dB of received signal level (RSL) at the receiver when in turn, the transmitter has the same and different polarisation with the receiver. A antenna with this greater value is prefered. This information is useful in microwace design when in the same area we can use the same frequency with different polarisation . For example: TX1 : vertical polarisation ---> RX1 : Vertical pol. TX2 : horizontal pol. ---> RX2 : horizontal pol. They all operate in the same frequency. The signal from TX1 , TX2 will be separated corresponding to the value of XPD.
Secret slab Pokemon Mystery Dungeon explorers of sky?
IT'S AN AWESOME ITEM. here are the codes to get it[course you have to beat the quest first]Effect:can "attract" legendaries in dungeonslike:Zapdos:Amp Plains 7F, Moltres: Giant Volcano 10F, Darkrai,Miracle Sea (DPB3F)Lower Crevice Cave (DPB2F)Mt. Travail (17F)Spacial Rift (14F)Mystifying Forest (13F)[srry i am kind of copying] Latios Midnight Forest (24F)Deep Spacial Rift (5F) , Latias Happy Outlook (19F)Spacial Rift (10F) , Ho-oh mount mistral 19F, Lugia Surrounded Sea 18F, Raikou Concealed Ruins 20F, Entei Deep dark crater 10F, Celebi Mystifying Forest 10F, Deoxys Shimmer Hill (17F) , and a little bit MORE. [some of these are wrong i don't remember a lot though sorry]quest codes:8-RX1 %52X=9S P24RJKPHQM 9@&N#JN 4+Q+CX-HY NSM8 6&3&2Q&P 520# 7WQ8Hope this Helps![at least a little?]I think the Slab allows you to find Deoxys in all forms at Temporal Tower
How do you check to see which element is bad in a hot water heater with an ohms meter?
To check which element is bad in a hot water heater with an ohmmeter, you need to disconnect the power supply, remove the access panel, and locate the heating elements. Set your ohmmeter to the appropriate resistance setting and test the resistance across the terminals of each heating element. If the resistance reading is extremely high or low, then the element is likely faulty and needs to be replaced.
How Countiniuty check by ohmeter?
Continuity means a direct connection or low Ohms or zero Ohms. A wire and switch will read from 0 to 0.1 Ohms on a perfect meter. A light bulb might read 1 to 10 Ohms, as example. First, to see if the meter is working properly: To check how the meter reads continuity and see how to interpret, touch the probes together and note the reading. This is the reading you should see when testing the circuit if you have good continuity. Safety!: Never test continuity or ohms on a circut that has power energized. The meter can be destroyed internally, or even explode if Ohms function is used on high voltages. Now, a couple ways to check: 1.) DIGITAL METER: Put the ohm meter on the lowest Ohms scale, usually will be "200". If the meter does not have several separate Ohms switch positions, it might be an "auto-range" kind. In that case, just set it to Ohms. 2.) ANALOG METER: Put the ohm meter on the lowest Ohms scale, usually will be "RX1". Some inexpensive analog meters have only one range, so just select the Ohms function, or plug the probe into the Ohms jack. Put the probes to what you want to measure. the reading should be zero if measuring continuity. In some cases, the digital meter may indicate between 00.0 and 00.6 Ohms, this is normal because even the wires and probes have some resistance. The lower, the better. Note that very inexpensive analog meters cannot read Ohms this low accurately, but you can tell if the continuity is good or not, because it will read "0" or very close to that.
How do you test fluorescent lighting circuit?
Continuity of electrical cables must, because it is the process of inspection to found any discontinuity in the cable
