answersLogoWhite

0


Best Answer

All Golf clubs are measured in inches. Just a shaft is simply measured top to bottom. When a golf club is assembled, with a head and grip, an iron is measured from the top butt end of the grip to the bottom of the hosel. When a wood is being measured it should be measured to the closest point of the sole to the hosel.

User Avatar

Wiki User

14y ago
This answer is:
User Avatar
More answers
User Avatar

Wiki User

12y ago

It's hard to explain but I'm going to try my best. Try any IRON of the same number but different sizes. Place your club in your hand with the correct grip as if your about to hit a golf club and stay in your posture. Let some one else look at your club face and he has to see if the clubs flange (bottom of the club, the first thing that touches the grass) is completely flat agains the ground. If the club is to long then that means that the toe of the club is lifted up and if the club is to short then that means that the neck of the club is lifted up.

This answer is:
User Avatar

User Avatar

Wiki User

14y ago

You take the grip and tape off the club, then you either use a circular saw blade to trim the shaft or use a specialist shaft cutter to take off the desired length. Then just regrip the club as normal.

This answer is:
User Avatar

User Avatar

Wiki User

15y ago

Measure from the top of the inside of your wrist, basicaly where your wrist and hand meet, measure from there to the ground. I know I am 38" inches from wrist to floor so that tells me that I need at least +1/2" or 1" in length and at least 1* in lie adjustment.

This answer is:
User Avatar

User Avatar

Wiki User

15y ago

It is suggested that you get your club pro to do it. To DIY you would remove the grip and grip tape residue, measure how much you want to take off it, mark it, and using a circular saw begin to cut it turning the shaft as you go to get an even cut, then simply put a new grip on.

This answer is:
User Avatar

User Avatar

Wiki User

11y ago

Measure it with a loft/lie measuring gauge.

Or you can try the following method using a carpenter's square and a measuring tape to measure the angle of the shaft when the face is vertical.

  1. Prop the club in a corner on a flat surface such as a workbench or counter.
  2. Using a carpenter's square, draw a line on the surface that's perpendicular to the wall and even with the corner that the club is propped in.
  3. Using the square, rotate the head to make it square with the counter edge.
  4. Keeping the head square, slide it back and forth until the lie is right. This will vary by club. Either get the leading edge flat with the surface, or move it until the center of it's curve is touching the surface.
  5. Turn the square vertical against the middle of the face of the club and slide the club head in a line parallel to the edge of the counter ( you may want to draw a pencil line on the counter ) until the center is vertical, i.e. flush with the vertical edge of the square, making sure that the face remains horizontally square with the counter edge. It's easier to do than describe. Double check that the face is square with the edge of the surface when the vertical seems right. Keep adjusting until the club face is square both ways.
  6. Measure the distance from the center of the club head to the line drawn in step 2 keeping the tape parallel with the edge of the surface.
  7. Measure the distance from the surface to the point where the club contacts the wall it's leaning on.
  8. Divide the measurement from step 6 by the one in step 7.
  9. Go to a geometric table or online calculator and find the arc tangent (arctan) of the number from step 10. The result is the loft of the club.

Note: The geometry is right, but that doesn't mean doing it by hand will give results accurate to a degree.

This answer is:
User Avatar

User Avatar

Wiki User

16y ago

you get some one who knows what there doing

This answer is:
User Avatar

User Avatar

Wiki User

14y ago

Depends on the Club. Lower number clubs have a longer shaft, and a more vertical face.

This answer is:
User Avatar

User Avatar

Wiki User

16y ago

have one custom made

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you shorten a golf club shaft?
Write your answer...
Submit
Still have questions?
magnify glass
imp