answersLogoWhite

0


Best Answer

It seems that they are just steel.

User Avatar

Wiki User

12y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What type of metal are 12g CO2 canisters made of?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Engineering

How much does a pair of flip flops weigh?

depends where you want to buy your flip flops they can range anyware form $1 to $50


How many amps can 25mm sq electrical cable can carry?

A 25mm sq electrical cable is equal to a #4 AWG conductor. A #4 copper conductor with an insulation factor of 75 and 90 degrees C is rated at 85 and 95 amps respectively.


What is the process for designing VLSI and ASIC chips?

Step 1: Prepare an Requirement Specification Step 2: Create an Micro-Architecture Document. Step 3: RTL Design & Development of IP's Step 4: Functional verification all the IP's/Check whether the RTL is free from Linting Errors/Analyze whether the RTL is Synthesis friendly. Step 4a: Perform Cycle-based verification(Functional) to verify the protocol behaviour of the RTL Step 4b: Perform Property Checking , to verify the RTL implementation and the specification understanding is matching. Step 5: Prepare the Design Constraints file (clock definitions(frequency/uncertainity/jitter),I/O delay definitions, Output pad load definition, Design False/Multicycle-paths) to perform Synthesis, usually called as an SDC file(Synopsys constraint file, specific to synopsys synthesis Tool (design-compiler) Step 6: To Perform Synthesis for the IP, the inputs to the tool are (library file(for which synthesis needs to be targeted for, which has the functional/timing information available for the standard-cell library and the wire-load models for the wires based on the fanout length of the connectivity), RTL files and the Design Constraint files, So that the Synthesis tool can perform the synthesis of the RTL files and map and optimize to meet the design-constraints requirements. After performing synthesis, as a part of the synthesis flow, need to build scan-chain connectivity based on the DFT(Design for Test) requirement, the synthesis tool (Test-compiler), builds the scan-chain. 7: Check whether the Design is meeting the requirements (Functional/Timing/Area/Power/DFT) after synthesis. Step 7a: Perform the Netlist-level Power Analysis, to know whether the design is meeting the power targets. Step 7b: Perform Gate-level Simulation with the Synthesized Netlist to check whether the design is meeting the functional requirements. Step 7c: Perform Formal-verification between RTL vs Synthesized Netlist to confirm that the synthesis Tool has not altered the functionality. Step 7d: Perform STA(Static Timing Analysis) with the SDF(Standard Delay Format) file and synthesized netlist file, to check whether the Design is meeting the timing-requirements. Step 7e: Perform Scan-Tracing , in the DFT tool, to check whether the scan-chain is built based on the DFT requirement. Step 8: Once the synthesis is performed the synthesized netlist file(VHDL/Verilog format) and the SDC (constraints file) is passed as input files to the Placement and Routing Tool to perform the back-end Actitivities. Step 9: The next step is the Floor-planning, which means placing the IP's based on the connectivity,placing the memories, Create the Pad-ring, placing the Pads(Signal/power/transfer-cells(to switch voltage domains/Corner pads(proper accessibility for Package routing), meeting the SSN requirements(Simultaneous Switching Noise) that when the high-speed bus is switching that it doesn't create any noise related acitivities, creating an optimised floorplan, where the design meets the utilization targets of the chip. Step 9a : Release the floor-planned information to the package team, to perform the package feasibility analysis for the pad-ring . Step 9b: To the placement tool, rows are cut, blockages are created where the tool is prevented from placing the cells, then the physical placement of the cells is performed based on the timing/area requirements.The power-grid is built to meet the power-target's of the Chip . Step 10: The next step is to perform the Routing., at first the Global routing and Detailed routing, meeting the DRC(Design Rule Check) requirement as per the fabrication requirement. Step 11: After performing Routing then the routed Verilog netlist, standard-cells LEF/DEF file is taken to the Extraction tool (to extract the parasitics(RLC) values of the chip in the SPEF format(Standard parasitics Exchange Format), and the SPEF file is generated. Step 12: Check whether the Design is meeting the requirements (Functional/Timing/Area/Power/DFT/DRC/LVS/ERC/ESD/SI/IR-Drop) after Placement and Routing step. Step 12a: Perform the Routed Netlist-level Power Analysis, to know whether the design has met the power targets. Step 12b: Perform Gate-level Simulation with the routed Netlist to check whether the design is meeting the functional requirement . Step 12c: Perform Formal-verification between RTL vs routed Netlist to confirm that the place & route Tool has not altered the functionality. Step 12d: Perform STA(Static Timing Analysis) with the SPEF file and routed netlist file, to check whether the Design is meeting the timing-requirements. Step 12e: Perform Scan-Tracing , in the DFT tool, to check whether the scan-chain is built based on the DFT requirement, Peform the Fault-coverage with the DFT tool and Generate the ATPG test-vectors. Step 12f: Convert the ATPG test-vector to a tester understandable format(WGL) Step 12g: Perform DRC(Design Rule Check) verfication called as Physical-verification, to confirm that the design is meeting the Fabrication requirements. Step 12h: Perform LVS(layout vs Spice) check, a part of the verification which takes a routed netlist converts to spice (call it SPICE-R) and convert the Synthesized netlist(call it SPICE-S) and compare that the two are matching. Step 12i : Perform the ERC(Electrical Rule Checking) check, to know that the design is meeting the ERC requirement. Step 12j: Perform the ESD Check, so that the proper back-to-back diodes are placed and proper guarding is there in case if we have both analog and digital portions in our Chip. We have separate Power and Grounds for both Digital and Analog Portions, to reduce the Substrate-noise. Step 12k: Perform separate STA(Static Timing Analysis) , to verify that the Signal-integrity of our Chip. To perform this to the STA tool, the routed netlist and SPEF file(parasitics including coupling capacitances values), are fed to the tool. This check is important as the signal-integrity effect can cause cross-talk delay and cross-talk noise effects, and hinder in the functionality/timing aspects of the design. Step 12l: Perform IR Drop analysis, that the Power-grid is so robust enough to with-stand the static and dynamic power-drops with in the design and the IR-drop is with-in the target limits. Step 13: Once the routed design is verified for the design constraints, then now the next step is chip-finishing activities (like metal-slotting, placing de-coupling caps). Step 14: Now the Chip Design is ready to go to the Fabrication unit, release files which the fab can understand, GDS file. Step 15: After the GDS file is released , perform the LAPO check so that the database released to the fab is correct. Step 16: Perform the Package wire-bonding, which connects the chip to the Package.