0
Why does the right blinker blink very fast then when the brake pedal is pressed it slows down and sometimes stops blinking altogether?
Wiki User
∙ 19y ago
It usually means you have a bulb burned out on that side. I can't remember if it's front or back.
Wiki User
∙ 19y ago
Add your answer:
Earn +20 pts
What is a 2002 VUE trying to tell you when you press on the brake and the right blinker lights up as long as the pedal is pressed?
Your rt side brake light is burned out.
Why is the ring around the power button blinking on your emachines computer?
This signals that the computer is in a standby or "sleep" mode. Most parts of the hardware are turned off by the BIOS until a key on the keyboard is pressed or the mouse is moved.
Replace wheel stud on a 1995 T-100?
They are usually pressed in & have to be pressed out. if you are lucky & is screw in type, You can double nut & turn. Sometimes a c clamp works for press if not too snug
How can you get the hazard lights to keep on blinking while the brake pedal is pressed in a 1998 Chevy Tahoe?
You can't. If the lights didn't stop blinking, no one would know you were stopping. Re: I gues that´s the point of the third light, because when you are stopped, no one knows, you are about to do something else, like backing to park, or that you are stooped and they need to go around you...
2000 Grand AM GT constant blinker sound removed hazard fuse still makes sound unless hazard switch is pressed and then the blinkers don't work How do you fix this?
switch is bad DON'T ALWAYS LISTEN TO MECHANICS, YOU CAN FIX IT YOURSELF. The contacts from your blinker switch are dirty. Here is a forum that tells you exactly how to clean it http://www.grandamgt.com/forum/showthread.php?t=50126&highlight=clicking+signal+light
Where can you find a World War 1 trench knife w pressed knucks?
you can sometimes find one for bid on EBAY.COM but very expensive......
How do you know if the Rear Wheel Bearings need Pressed in or not on a 2004Hyundai Sonata 4-cylinder?
Wheel bearings should always be seated. check for clearance behind them after they have been installed. if there is play then there is a problem. However after being a mechanic and an industrial technician for 14 years now I can honestly say that I have never seen a set of roller bearings being pressed in. the very nature of roller bearings does not allow for them to be pressed. The bearings roll on the shaft and the housing. if they were pressed in then the retainer that holds them together ( making up the body of the bearing) would be crimped, thus destroying the bearing. Industrial applications usually require the bearings to be pressed, but are differently designed altogether. Also if the bearings came out by hand easily then they were not pressed in. Even if they were just a little firm. This just indicates that they just had a little weight on them in operation.
Are rotors on a 1995 Saturn pressed on?
No, they are not pressed on.
What do we get cider from?
Cider is made from apples. In the UK the pressed juice is fermented to make an alcoholic drink. In the USA the juice itself is sometimes called cider.
1 brake light works other one quit fuses good third brake light wworks bulbs good 1988 olds cutlass supreme?
its the blinker control arm.if you move it back and forth you should see the two other brake lights go on as the brake is pressed.
What is the problem 1998 Volvo s70 driving mode lights and arrow on dash are blinking?
The "W",winter mode button is pressed and you probably put the gear selector lever in position "3". Put selector lever in "D" and press the "E" economy mode button.
What is laminate rifle stock?
Sheets of different woods are coated with glue, pressed together, and when glue has set, wood is carved into a rifle stock. See the link below for pictures. Sometimes done for strength, sometimes for appearances.
