0
The forcing cone is the constriction at the end of the chamber in a shotgun barrel that forces the load down from chamber size to the size of your shotgun bore. If you hold the barrel up, point the muzzle toward the light and look through it from the chamber end, the forcing cone will appear as a short, dark ring, dark because the angle of the short forcing cone is severe and is hidden from the light. The distance from the beginning to the end is about 1/4 - 1/2", give or take. Most barrels come from the factory with this abrupt constriction, or forcing cone.
When the shotgun is fired, the shot load is immediately FORCED, under tremendous pressure, to squeeze through the abrupt forcing cone to the smaller size of the bore. The shot in the back of the load move first and they have to push the guys in front of them through that abrupt forcing cone. This results in some of the lead shot becoming deformed, making them ballistically unsound and causing them to fly out of the pattern. Lengthening the forcing cone by changing the abrupt angle to a more gentle, gradual constriction results in a new length of around 1 3/4" and a much more gentle angle of constriction. This optimum new length and less severe angle from chamber ID to bore ID allows the shot to make a more gradual transition from chamber to bore size, reducing shot deformation and allowing more of the shot to remain in the pattern.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What Is A Forcing Cone?
The rear of the barrel of a revolver handgun, directly in front of the cylinder has a cone shape. That shape, known as a forcing cone, serves to guide a bullet into the barrel as it is fired.
Do shotgun barrels scratch from shooting?
Depends on age of the barrel, forcing cone type and the shot used. a new Remington 870 will not scratch. an old Winchester m12 will scratch when using steel. lead is good for old barrels, steel wrecks them.
What is the name of the old shotgun with the very large cone end on the barrel?
blunderbuss
How 2 cut a double barrel shootgun?
Federal law requires that the barrel be no less than 18" long as measured from the front of the chamber (at the forcing cone).
What are the sentence for forcing?
Sentence for forcing: Why are you forcing me to do this?
What is louder 380 pistol or 38 special smith and Wesson?
A revolver is louder than a pistol due to the barrel-cylinder gap that is located between the cylinder face and forcing cone of a revolver.
Can a marlin 200 410 shoot magnums?
The 12 g Marlin 200 single shot shotgun SHOULD be marked on the barrel, something like "model 200 12 g 3" Modified" That means it will fire the 3 inch magnum shotshell, and has a modified choke. If you have a shotgun marked 2 3/4, do NOT fire a 3 inch magnum, even if it will chamber. The forcing cone will not have enough length for the shell to open, and it will cause unsafe high pressures. Every 200 I have seen (a limited number) WAS chambered for 3 inch Magnum shells.
What could cause ejection problems in a Browning BPS when shooting 3.5 inch shells?
If the gun is not chambered for the 3.5 inch shells, they will get stuck in the forcing cone. To the person asking the question you can rest assured that there is a problem with the ejection part of your shotgun ,because I had one that did the same thing and I had to take it to a gunsmith and he had to file down the ejectors,,, I believe that's what he called them. As for the first answer you couldn`t get a 3.5" shell in the gun without realizing something was wrong.
Is Mount Kenya a composite cone a cinder cone or a shield cone?
A shield cone.
What is a cone bearer?
A cone bearer is a cone that bears
What are the pitfalls to shooting 3 inch magnums in a 2 and three quarter inch chambered JC Higgins Model 20 12 gauge?
The JC Higgins Mod 20 is a High Standard Mod 200, an aluminum frame shotgun, so I see only a couple of problems. The High Standard company went out of business before 3" magnum shells were released to the market, so their shotguns were never designed for the higher pressures of magnum shells. In addition, the longer shell would protrude into the forcing cone at the breech end of the barrel and when the shell was fired, the folded end of the shell would be impeded from unfolding by the forcing cone, resulting in higher pressures. These two factors could well combine to shatter the receiver and blast aluminum shrapnel into your face. Other than that, no problem.
Is the cone shape a circle and triangle?
Neither. A cone is a cone.
