0
pull pin under barrel it may be stuck
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Looking for part to hold cylinder in placeon a 22rg14s pistol that locks the cylinder in place so it will shoot?
Try a gun shop or a good gunsmith might be able to make one.
What is the Clerke technicorp 1st six shot pistol revolver?
If memory serves me right, Clerke's were prototypical of what was referred to as a "Saturday night special". Made from cast alloy (Zinc and/or low grade aluminum primarily) most were chambered for low-pressure cartridges -- .22LR, .32 S&W (not long) mostly and the .38 S&W (not special). If one of these guns survived firing more that 200 rounds, I'd be surprised. One specimen that I saw -- in .22 caliber -- you could see where the sprue holes were in the casting mould as they had barely polished (not machined) them off. The .38 S&W was better finished but it had fallen from an idiot's pocket in a parking lot. The fall not only popped the cylinder open, it cracked it and fractured the joke they called the cylinder crane.Clerkes made the RG/Rohm guns look like premium guns.
Has any one seen a pistol with these markings 22 cal pistol with a crown a jewel and omega symbols on the bottom of barrel It is old?
yes i have one. i am trying to find out some info on it also. the symbols are on the barrel right in front of cylinder.
What do you have to do to remove a starter for a 1988 Chevy Cheyenne 6-cylinder standard trans?
you must remove the clutch slave cylinder and line. Then unbolt the starser and install the new one
How do I remove and replace the master cylinder on a 1991 Chrysler New Yorker?
Disconnect brake lines Remove mounting bolts Remove Master cylinder Besure to "bench Bleed" new one prior to install
Percussion pistol firing moe than one cylinder?
I assume that you are asking about a cap and ball revolver. It's called chain firing. When one cylinder fires, it sets off one or more other cylinders. When you load the pistol, use a lubricated pistol wad between the powder and the ball, or cover the ball with grease such as Crisco, or bore butter. Chain fires can also be caused by loose or poorly fitting caps. Make sure they fit snugly. If the pistol has chain fired, it's best to have it checked out by a gunsmith for damage before firing it again.
How do you remove key cylinder on a 1997 Lincoln mark viii?
There are two (2) torque screws that hold the cylinder itself onto the car. Remove both and the cylinder should fall out. (this is the hard way) Remove one (1) Torque screw, bottom. Then turn the key to the ON position (not running) and then press the tab that holds the cylinder in and the cylinder itself should fall out. (this is the easy way)
How do you replace the clutch slave cylinder on a 1998 subaru legacy?
remove the old one and install a new one.
How do you change the master cylinder on Nissan pick up 1984?
go to one of your bleeder valves ,and drain brake fluid,then remove end ofrod from brake pedal , then remove bolts holding master cylinder on.take off and put new one in.
Where to find 22 magnum cylinder for rohm model 66 pistol?
If anyone is still looking for that 22 mag cylinder for a RG model 66 revolver I have one. I am willing to trade it for the 22 LR cylinder. I have two of the mag cylinders and want the 22 LR one for a cheaper way to just have fun with the gun. I have an extra 22 LR cylinder, will trade....taurush@suddenlink.net
How many bullets can a pistol or a revolver hold?
That number of rounds can vary. Most of us are familiar with revolvers that hold six rounds. Some pistol magazines can hold up to 13 and more. I know of one revolver with a cylinder that holds nine rounds.
How do you remove the key cylinder on a 1991 Ford E150 van and install a new one?
call a locksmith
