answersLogoWhite

0


Best Answer

The blade will have glue on it when you purchase it. Heat the end of the blade that goes into the shaft, preferably with a heat gun, until the glue softens.If you dont have a heat gun, you can use a torch. Lightly heat the inside of the shaft as well, and then push the blade down into the shaft, with the butt end of the shaft on the floor. Avoid putting too much heat to the shaft, as it could damage the shaft.

User Avatar

Wiki User

17y ago
This answer is:
User Avatar
More answers
User Avatar

Wiki User

15y ago

wood sticks its easy...composite not so much. get a torch, heat the sucker up without setting it on fire and bend it and let it cool

This answer is:
User Avatar

User Avatar

Wiki User

14y ago

You can simply use hot glue for a regular glue gun. I have used this many times on replacement blades.

This answer is:
User Avatar

User Avatar

Wiki User

12y ago

Take the inside soles of the shoes out and you will see screws.

This answer is:
User Avatar

User Avatar

Wiki User

15y ago

glue it together and then use a blowtorch

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you attach a blade to an aluminum hockey stick shaft?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

What is the bottom of the lacrosse stick called?

On the hockey stick, you have the shaft (the part you hold), and the blade (the part that touches the ice). In the blade, you have the Heel, which is the part connected to the shaft. Then you have the toe, which is the tip of the blade, or the end which does not connect to the shaft.


Can a Easton hockey shaft hold a Bauer blade?

Yes


Is a hockey shaft and blade as long as a onepiece stick?

yes


What is the lie in a hockey stick?

the curve from the shaft to the tip of the blade


What is taper on a hockey stick?

The area near the bottom of the shaft where the width of the shaft decreases as it gets closer to the blade.


Can a 520 hockey blade work with a 620 hockey shaft?

yes but it's complicated to do. you have to put a layer or two of tape inside the shaft and then heat it up and glue it. depending on how much the blade was it may not be worth the hassle.


The angle formed between the blade and the shaft of a hockey stick is 135 What type of angle is this?

Obtuse.


Can you remove the blade from a 2 piece hockey stick and reuse it?

Yes, the blades are just glued into the shaft. Use a heat gun to melt down the glue, pull out the blade and put it in your new shaft.


Can you reuse a broken hockey stick?

No, a player will get penalized for continuing to play with a broken hockey stick. Sometimes, a hockey shaft and blade are two pieces and can be replaced. Otherwise, you usually have to get a new one.


Can you use metal hockey sticks?

In ice hockey, sticks may incorporate metal, and aluminum is a common choice to make the whole shaft from. In field hockey, metal is banned from use in sticks for safety reasons.


What type of stick hits a hockey puck farther?

This depends on the flex rating/capability of the stick shaft, the strength of the stick blade and the power of the player shooting the puck.


How do you replace a hockey blade in a shaft over a stove?

turn on ur oven burner to atleast 115 dagrees and twist ur stick around slowly by the blade on all 4 corners for a 1mins to take out the old blade than heat the glue over the stove for 45 seconds than rub the glue on all 4 corners of the top of the blade than place the blade into the shaft furthermore twist the stick around by the 4 corners where the blade went into the stick at for 1mins than let the stick rest and cool for 1mins for the shaft expand back to the way it always was like so the blade can adapt to the stick than after 1min go out side and enjoy ur total annihialtion hockey games or practice wrist shots or slap shot or snap shot or whatever shot and watchout for the amazing accuracy it will pay off!!!!!!!!!