0
Can you change a ripstik wave face plate with a ripstik faceplate?
Guitarhero1225
yea its quite easy, doesn't exactly pop right on and off but works well, my son did it
Wiki User
∙ 14y ago
Wiki User
∙ 14y agogold and silver
Add your answer:
Earn +20 pts
What is a faceplate?
Face Plate is used on Lathe machine. It is just like lathe chuck. irregular shape job clamp on face plate by clamps, bolts.
How do you fix lights in a faceplate?
If it's a removable faceplate, try tightening the screws on the back of the face plate. If that doesn't do it and the face plate isn't motorized, check the contacts on both the head unit and faceplate to see if they are out of whack. If your faceplate is motorized, it's probably the ribbon cable and should be taken to a service center. If the faceplate isn't removable at all, your best bet is to just take it into a service center or buy a new head unit.
How do you replace the poo skimmer door?
Drain the pool until the water level reaches two inches below the skimmer faceplate , remove the face plate using a screwdriver , remove the faceplate and skimmer , then replace the gasket and attach the skimmer and then the faceplate
Where can I find a Face plate for a Power Craft wood lath?
Oneway makes them. What you must do is determine the diameter of the spindle and the number of threads per inch it has. Once you know that, you can order a faceplate.
What are face plates used for on the lathe machines?
On a wood turning lathe, the faceplate is screwed to the piece of wood, then the faceplate is held in place by the chuck. This facilitates free-wheeling the opposite end for such items as bowls. Almost similar to a wood turning lathe, the face plate on a metal lathe is a device that is used instead of a chuck. It allows a workpiece to be clamped or bolted to it for machining.
What is the plastic clear cover on watch called?
The plastic clear cover on a watch is called a protective film. It is used to keep the glass face plate from getting scratches or getting damaged or cracked. ADDED: The first answer is referring to the protective film applied at the factory which protects the watchface "glass faceplate" lens. The name of the glass faceplate is called the "BEZEL." ANOTHER ANSWER: The glass that covers the watch face is also called a crystal.
How do you remove the factory radio from a 2000 Ford Expedition?
Need either special tool or perhaps paper clips inserted in small holes at corner of face plate. After releasing faceplate you should have access to mounting bolts
How do you remove the factory stereo from a 2008 subaru impreza?
recommendations on older models suggest using a flathead screwdrive to pry off the faceplate to gain access to the stereo which is held in by 6 screws as far as I know. I'm still looking for answers myself. On the Impreza 2008 2.5I,pry off the lower face plate (with the HVAC controls),it is easier to start prying by the glove compartment(be gentel),you do not have to completely remove this face plate just loosen it till you have room to pry off the radio face plate(as it is cliped under the other faceplate),there you will have access to the 4 Phillips screws!!!!!!!! Tools needed: -Flat head screwdriver -Phillips screwdriver
How to find a used detachable face plate for radio CD player 2001 Kia Sportage?
youll most likely have to replace the whole radio. from what ive been told it would cost the same or more just for the faceplate alone.
Can not get the sony cdx-gt100 CD to reset?
1 turn off the ignition and then turn it on and then off. 2 take off the faceplate of stereo. 3 then throw your face plate in toilet. 4 buy new system you cheap people.
Can you purchase a titanium face plate for your Droid cell phone?
It is possible to purchase a Titanium faceplate for your Droid phone in a wide variety of colors. Since this is a specialty item it is recommended to check out online specialty stores or even stores at your local mall which carry cell products.
How do you reset jvc kd r420 car radio?
Remove the faceplate. There is a small hole labeled reset. Use a pen and gently insert it into the hole . You will here a click . That's it!
