Can the trigger frame on an auto-cocker come off?

How do you remove Tippman trigger slider?

First take off the bolts then the safety push will come out and then just take it off

How do you remove the body off the chassis of a 1963 Impala SS?

there are bolts that go through the frame to the body that have to come out before you can raise the body off the frame, also all wiring has to be disconnected from the motor and the firewall.

Where is the battery compartment located on the vulcan EBF-25?

unscrew the screw under the gun closest to the trigger then a part of the bottom will come off and a tray will will come out then put the 6d batteries in then do the steps backwards then your on your way

What is an autococker pump gun in paintball and how is it good?

It's a semi-auto autococker with its front pneumatics taken off and pump handle put in it's place. As for how it's "Good" is all a matter of preference. Some people enjoy the thrill of using a pump, while others like me are just too broke to by a case of paint for a day of paintball

Does subframe have to come off to remove gear box on pug 307 2o hdi?

The sub frame does not need to come off in order to remove the gearbox. The gearbox can be removed by removing the engine.

Can you put an e trigger on an old tippmann 98?

98? or 98 custom? I don't think you can put one on the old 98s or the customs actually there might be a special made e-trigger for the 98 customs but the reason why I say you cant is because if you look at a 98 custom or 98's inside theres no where really for the whole trigger to come off whereas the A5 or X7 the entire trigger system comes off handel, trigger, firing modes, everything its basically half of the back part of the gun coming off

How do you get the trigger and trigger guard off of a nepalese 1851 enfield rifle?

Best to ask a gunsmith for assistance.

What is the best thing you can do to your autococker?

It depends on what you think is "best". for the "best" accuracy, you should get a barrel kit for the gun. For the best safety, you should get a On/Off ASA. For the best performance, you should purchase a board and different style triggers.

What does chocolate and laughing trigger off in the body?

Endorphins

How can i remove the doorpanel off a kia picanto?

Using a screwdriver, remove the screws and the clips in the door panel, then slowly pull the panel off the frame. Remove the wiring connections, and the panel will come free.

What is trigger part of?

A trigger could be part of a firearm. It could also be a word meaning to start an action, as in: the fire alarm going off was the trigger that started the evacuation of the building.

How do you disassemble a SW 686 revolver?

Basic: 1. Place unloaded revolver on half cock2. Push Barrel Wedge to the left. It will either stop against the retaining screw or come all the way out. This varies.3 pull barrel assembly off the frame and cylinder off the arbor.4. Unscrew nipples for cleaning.Complete:1. Remove back strap section of the grip frame. Screws are on either side of the hammer and on the bottom of the grip frame assembly.2. Loosen and/or remove the main spring;3. Remove front of grip frame/trigger guard - three screws.4. Remove Trigger bolt spring now visible in the bottom of the action.5. Remove cylinder bolt and then trigger held by identical screws.6. Remove hammer screw and then hammer and hand assembly through the bottom of the frame.Remounting:1. Replace hammer and hand first being careful not to compress or overstress the hand spring'2. Replace locking bolt. It is necessary for the split "ears" on the rear of the hand to ride in front of the cam on the right side of the hammer. This is best accomplished by placing the hammer in its lowered (forward ) position. The outside "ear" presses against the inside of the frame while the active side presses against the hammer in front of the hammer cam.3. Replace Trigger. This is easiest with the hammer pulled back.4. Replace trigger /bolt spring being sure that the long "finger" is on the step on the front of the trigger. Some springs appear to be too short to replace. In this case, index the long "finger"/leaf of the spring against the step on the trigger and press down so that it will stretch out and allow replacement of the screw.5. Replace front porton of grip frame and the main spring. It is often best to leave some slack in the screws-including the mainspring screw- until everything is in position. then tighten all screws.6. Replace grip and back strap of grip frame. This may require loosening the screws of the front portion of the grip frame just to get all the screws lined up.