0
Can my ten and a half foot long longboard be used as a stand up paddle board?
Wiki User
∙ 11y ago
Many long boards can be used as a Stand Up Paddle board, and many of them are becoming more flexible and can also be used as a sit-on-top kayak when a seat is added.
Usually, SUP boards are 11 - 12 feet long. The weight cut-off is 170 pounds - use 11 foot board if you are under 170 - use 12 foot board if you are over. However, lighter weigh people can use shorter boards. The water conditions also need to be considered - surf, flat water, rough water.
If you can balance well on the board, without the tail dragging or the nose dipping, the board will probably work for you.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Which of these is used in downhill skateboarding longboard shortboard inclined board?
the force of gravity, natural force(weight), the applied force(your pushing off of the ground with your foot), and the frictional force.
How do you size a SUP paddle board?
Sizing your Stand up Paddle Board is dependent upon a lot of items, such as water conditions - flat water vs. rough water vs. surf. The short answer, if you are just beginning to do SUP is that the cut-off weight between an 11 foot board and a 12 foot board is about 170 pounds. If you are below 170 pounds - choose an 11 foot board. If up are above 170 pounds, a 12 foot board will be a better choice. If you are a light-weight, you can go less than 11 feet. One important consideration is being able to carry your board. If you are a light weight and prefer a 12 foot board, but you can't carry it, it isn't very practical.
How do you cross step on a longboard?
You have to get far back on your board, you leave the front foot at a slight angle (around 45 degrees), then step your back foot in front (you will need practice, it might be hard to balance at first). then pop your front foot back into the front position. When you improve, do it carving.
What is the purpose of a longboard tail?
The tail of a longboard provides added foot room, and also usually serves as a way for the rider to lift the board to either maneuver curbs or turn sharply. The curvy tails are usually only seen in smaller boards and cruisers. The shape of a tail can also contribute to a minuscule amount of aerodynamics.
Could a human jump off of a longboard at 20 mph and stop safely?
No. lear how to foot break.
Is A Skateboard 10 foot long?
easy.... no... thats a longboard... usual skateboard length is 32 inches with various widths...
How does a person ride a skateboard?
You put your feet on the part of the board with grip tape and push off with one foot if you're on flat land. If you're on the top of a half- pipe, you should stick with putting on foot on the board, letting half of the board go over the ledge, then put your other foot on when you go down the half- pipe. Don't try any tricks until you can stand on a board without falling.
What is stand on one foot?
Sleeping birds stand on one foot.
What should the width for a 9 foot surfboard be?
Depending on shape (Gun,Performance longboard etc.) 20 1/2 - 24"
How long is a board foot?
The board-foot is a specialized unit of volume for measuring lumber in the United States and Canada. It is the volume of a one foot length of a board one foot wide and one inch thick.
What is a 2.9 Board foot?
A board foot is 12 inches by 12 inches, 1 inch thick. Any combination of measurements that equal this is 1 board. 6x24x1 is 1 board foot. 2.9 board foot could be anything. There should be another measurement saying what this is. Board foot is used to figure cost as most common wood is the same price per board foot. Could be 2x4, 2x12 or 1 inch, it all works out the roughly the same price.
How many 6 x 6 blocks can be made out of a 4 foot board?
Assumption: 6 x 6 is using inches as the unit (half a foot) and a 4 foot board means 4 square feet of board. Each square foot of board can be cut into four half foot x half foot pieces. Therefore, the 4 foot board would be able to make 16 half foot x half foot (6 inch x 6 inch) blocks.
