Best Answer

the ring gear? 10 bolt. the cover? 10 bolt.

User Avatar

Wiki User

โˆ™ 2006-09-03 04:35:02
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How many bolts are on the differential of a 1992 S10?
Write your answer...
Sign up for more answers

Registered users can ask questions, leave comments, and earn points for submitting new answers.

Already have an account? Log in

Related questions

How many bell housing bolts in 01 s10 4.3?


How many bolts hold bed on Chevy S10?

there are 8 on a 6 foot s10 bed plus the filler neck

How many bolts are on a 97 S10 alternator?

If I remember correctly, my '98 (2.2l 4-cyl) alternator has two bolts.

What is the speaker size in a 1992 s10?

What size are the speakers in a 1992 standard cab Chevy S10?

Where is the ECM located in a 1992 Chevy S10 blazer?

The ECM on a 1992 S10 Blazer is located below the glove box.

What is the towing capacity for a 1992 half ton Chevy S10 pickup truck?

how much can a cheve s10 1992 pull ?

Where is the fuse for the digital cluster dash in a 1992 Chevy S10?

Where is the fuse for the digital cluster dash in a 1992 Chevy S10?

Will rims from a 1996 s10 fit on a 1992 s10?

yes and they look pretty good

What size is the rear differential on a 1994 Chevy S10 with a 4.3L V6 4 speed auto transmission and 2WD?

The rear differential on a 1994 Chevy S10 with a 4.3L V6 4 speed auto transmission and 2WD has a capacity of 4.1 pints. Use the manual to get more information on the rear differential.

How many quarts of gear oil does a 2000 Chevy S10 take?

If you are filling the rear differential, 3 and 1/2 pints should do it.

How do you clean the carburetor on a 1992 s10 pickup?

The 1992 S10 doesn't have a carburetor. It more than likely has TBI (Throttle Body Injection).

Can you disconnect the differential on your 1991 S10 Blazer?

Sure... you pull out the axle shafts, and its disconnected.

89 s10 jumping out 1st gear?

1992 Chevy s10 jumps out of 5th gear

How many bolts hold the transmission to the 4.3 engine of an s10 blazer?

im puttin in a 96 jimmy engine in my 2000 blazer and there are 9 bolts..(had to go buy them at hardware store)...

1992 s10 4.3 vortex the same as a 1996 s10 blazer?

block and heads are the same but not the computers

Does a 1992 Chevy s10 pickup have air bags?

No. Air bags were introduced on the 1995 S10 Chevrolets.

Is the body of a 1992 s10 pick up the same as a 1995 s10?

nope, gm overhauled the S10 in 1994 so the body is completely different

How do you go about removing the rear seat in an 1989 S10 Blazer?

take the bolts out

What is the torque spec for clutch plate Chevy 1997 S10?

1997 S10 4 cylinder engine pressure plate to flywheel bolts, 33 ft lbs.1997 S10 V6 engine pressure plate to flywheel bolts, 29 ft lbs.

Where is the vehicle speed sensor on a 1995 s10 pickup?

The vehicle speed sensor on a 1995 s10 pickup 2wd is on the tailshaft of the transmission. The 4wd is mounted on the tailshaft of the front differential.

How do you change starter on 1992 s10 4.3 liter v6?

Disconnect the battery. From underneath, find the starter at the rear of the engine. Remove the wiring and the bolts from the starter. Drop the starter and install the new one.

What are the torch specs on the head bolts and intake manifold for a 1996 Chevy blazer s10?

Head bolts are 65 Ft. LBS Intake bolts are 35 Ft. LBS

How do you remove the driveshaft from a 1999 Chevy s10 pickup?

Make sure truck is level or pointing downhill is even better. Remove the 4 bolts at the differential. Pry the driveshaft forward. Slide the front out of the transmission. Hold the front most piece with your hand as it comes out of the transmission. At re-assembly torque the bolts to 15 ft/lbs.

What are the torque specifications for the head bolts on a 92 Chevy s10 2.2 L?

For the 1992 Chevy S-10, 2.2 liter, first tighten the cylinder head bolts to 40-47 ft. lbs. If you're using new bolts finishing tightening them to 54-61 ft. lbs. If you're using the original bolts, finish tightening them to 61-69 ft. lbs.

What is the bolt pattern on a 1992 S10?

THE BOLT PATTERN FOR THE WHEELS OF A 1992 S10 4 WHEEL DRIVE TRUCKwhat bolt pattern do you mean? The s10 pattern is 5 x 4.75. Also known as 5x4 3/4 or 5x120.7 mm