answersLogoWhite

0


Best Answer

2 bearings bear wheel 8 bearings total

User Avatar

Wiki User

โˆ™ 2011-12-31 22:13:12
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How many bearing in a skateboard per wheels?
Write your answer...
Submit
Related questions

How many bearings in a scooter?

For a kids push scooter, there are 2 bearings per wheel, 2 wheels per scooter. 4 bearings total. If you buy a pack of 8 for a skateboard, you will have 2 sets.


What amount of bearings make a skateboard work the best?

All 8 that should be in the wheels.. (2 per wheel.)


If a skateboard takes 1.47 seconds to go 10 feet how many miles per hour is it going?

The skateboard is going 4.64 miles per hour.


How do you repair a skateboard?

Repairing a skateboard can depend on many different factors, such as which part of the skateboard is damaged. There are several parts to skateboard, some of which cannot be repaired.If the deck itself is in need of repair for any reason, such as water damage or pressure cracks, then purchasing a new board might be your only option. If the damaged portion of the skateboard is replaceable, however, a simple trip to your local skate-shop can get you on your board again.Replaceable parts:Trucks: Consist of a hangar, a base-plate, a kingpin bolt/nut, two truck bushings, a pivot cup, a riser pad* (optional) and a set of four nuts and bolts that are used to fasten the truck to the skateboard. The base-plate is the rectangle shaped portion of the truck that is fastened to the skateboard. This is also where the kingpin is located. On the circular portion of the bottom of the base-plate is where one of the truck bushings is located. The wide portion of the truck, known as the hangar, is where the wheels are fastened. The second truck bushing is located on the circular portion of the hangar, similar to the base-plate, and sits right above the other bushing. The pivot cup is the small black circular hole that is located on the base-plate. This is another important, but often over-looked part of the truck. The tip of the bottom of the hangar fits into the pivot cup, and if the pivot cup is damaged, the truck may not turn at all, which may be dangerous. Note, there are two trucks per skateboard.Bushings: Bushings are what allows the truck to turn. They do wear over time, so check them regularly, just like any other part of the skateboard. If the bushings are damaged, they can start to split apart. This can cause the board to turn improperly, or jeer to the left or right when attempting to ride straight.Wheels: Wheels are probably replaced more than any other part of a skateboard. They can wear down, crack, and even "cone" after prolonged usage, especially if you like to slide your skateboard. There are four wheels to each truck, and each wheel must have two bearings. Wheels may also have two wheel-washers, and one bearing-spacer** (optional, but recommended).Bearings: Bearings, like wheels, are often replaced quite quickly, due to wear. Bearings are the small, circle-shaped, metal pieces that go into your wheels. They are fairly cheap and are important for going fast on your board, and for going for a long time. If your bearings are too worn-down, your ride will not be as enjoyable. To test your bearings, simply pop them out of your wheel, and spin them on your truck hangar or by holding one carefully with the tips of your fingers. If the bearing chunks, or makes a cracking noise and does not spin well, then it is recommended you replace said bearing.*Riser pads lift the truck from the board, and depending on the material, can cushion the ride. Riser pads can also prevent the skateboard from getting wheel-bite, if the risers are large enough. Wheel-bite occurs when the wheels are too big for a skateboard, and they "bite" the bottom of the board when the rider attempts to turn. Certain skateboards are crafted with wheel-wells, which allow the wheels to be larger, due to a cut-out in the wheel-area of a skateboard.**Wheel-washers and bearing-spacers are not exactly needed, but they reduce tension on the bearing, which prolongs the life of the bearings, and allows you to go faster and longer when skating.


What are the parts of a skateboard?

Skateboard PartsDeck: The deck is the main part of the board. It's what you stand on.Trucks: Consist of a hangar, a base-plate, a kingpin bolt/nut, two truck bushings, a pivot cup, a riser pad* (optional) and a set of four nuts and bolts that are used to fasten the truck to the skateboard. The base-plate is the rectangle shaped portion of the truck that is fastened to the skateboard. This is also where the kingpin is located. On the circular portion of the bottom of the base-plate is where one of the truck bushings is located. The wide portion of the truck, known as the hangar, is where the wheels are fastened. The second truck bushing is located on the circular portion of the hangar, similar to the base-plate, and sits right above the other bushing. The pivot cup is the small black circular hole that is located on the base-plate. This is another important, but often over-looked part of the truck. The tip of the bottom of the hangar fits into the pivot cup, and if the pivot cup is damaged, the truck may not turn at all, which may be dangerous. Note, there are two trucks per skateboard.Bushings: Bushings are what allows the truck to turn. They do wear over time, so check them regularly, just like any other part of the skateboard. If the bushings are damaged, they can start to split apart. This can cause the board to turn improperly, or jeer to the left or right when attempting to ride straight.Wheels: Wheels are probably replaced more than any other part of a skateboard. They can wear down, crack, and even "cone" after prolonged usage, especially if you like to slide your skateboard. There are four wheels to each truck, and each wheel must have two bearings. Wheels may also have two wheel-washers, and one bearing-spacer** (optional, but recommended).Bearings: Bearings, like wheels, are often replaced quite quickly, due to wear. Bearings are the small, circle-shaped, metal pieces that go into your wheels. They are fairly cheap and are important for going fast on your board, and for going for a long time. If your bearings are too worn-down, your ride will not be as enjoyable. To test your bearings, simply pop them out of your wheel, and spin them on your truck hangar or by holding one carefully with the tips of your fingers. If the bearing chunks, or makes a cracking noise and does not spin well, then it is recommended you replace said bearing.*Riser pads lift the truck from the board, and depending on the material, can cushion the ride. Riser pads can also prevent the skateboard from getting wheel-bite, if the risers are large enough. Wheel-bite occurs when the wheels are too big for a skateboard, and they "bite" the bottom of the board when the rider attempts to turn. Certain skateboards are crafted with wheel-wells, which allow the wheels to be larger, due to a cut-out in the wheel-area of a skateboard.**Wheel-washers and bearing-spacers are not exactly needed, but they reduce tension on the bearing, which prolongs the life of the bearings, and allows you to go faster and longer when skating.


How many bearings in every scooter?

2 bearing per wheel so there will be a total of 4 bearing in a whole scooter.


How many tires on a Boeing 777?

Wheels or tires? if tires, 14. If wheels, 7. There are 2 tires per wheel.


How many skateboarding injuries are there per year?

An estimated 50000 skateboard injuries are treated in hospital emergency rooms each year according to www.personal-injury-info.net/skateboard-injuries.htm


How many wheel bearings do cars have?

Cars have a total of four wheel bearings, one on each wheel. The wheel bearings are designed to help the wheels spin. Many cars have two wheel bearings per wheel, an inner and an outer located in each hub/bearing assembly.


How do you replace bearings on a skateboard?

Unbolt your wheels first, you will need a small socket wrench for this. Then push or pry out the bearings, there are two per wheel. Press in the new bearings and bolt it up again, but not too tight so as not to squeeze the bearings.


If you bought roller hockey skates with mini bearings can those same skates be switched to standard bearings?

Yes, any skate can take either bearing but you need to have the right type of wheel and spacer per bearing. ie, if you have mini bearings you need mini hub wheels and spacers that fit the mini bearings. If you have standard bearings you need standard hub wheels and spacers that fit the standard bearings.


How many lug nuts on a Cadillac Escalade?

5 per wheel x 4 wheels = 20 total


Will a skateboard go faster if you push it with the same force for a longer time?

Yes. The force is measured as "acceleration" and is meters per second per second (or velocity per second) or the first derivative of velocity. On a frictionless surface in an environment without air resistance, and if the skateboard is a frictionless mechanism, if the skateboard is moving at a constant velocity, that means the acceleration is zero, which means that there is no force being applied to it and it is a body in motion staying in motion.


How many bearings are in a skateboard?

Dude actually it's 8. 2 per wheel. Unless you ride a board with 1 truck on it there's 8. :O


How many lug nuts on a 1991 jeep?

5 per wheel x 4 wheels = 20 total


Aircraft Floor bearing weight?

Floor bearing weight: 140 lbs to 200 lbs. per sq. ft.


How many spokes are on a 26 inch bike wheel?

This completely depends on the wheel. The most common number of spokes per wheel is 36. Some better wheels have 32. Higher performance wheels have even less.


How many tire lugs on a Ford Windstar?

At 5 lugs per wheel x 4 wheels = a total of 20.


How many lug nuts on a 1996 cadillac deville?

5 per wheel x 4 wheels = 20 total


How many lug nuts on a 98 Cadillac Seville?

5 per wheel x 4 wheels = 20 total


What are the torque specs on a 2003 Malibu hub bearing?

The 2003 Malibu hub bearing torque specifications are 40 pounds per square inch. You can ruin the bearing by tightening it too much.


What is the weight of the new pinewood derby wheels?

The new wheels used today in the BSA kits were first created in 2009 and have a weight of 2.7 grams per wheel. The older wheels before 2009 had a weight of 3.6 grams per wheel.


How many wheel bearing does and 2000 Oldsmobile alero have?

2. front left and front right.


How many skateboard deaths are there per year?

On average 2006 had nearly one person killed per week while skateboarding; a total of 42 skateboarding youth died while recreating. Of these 42 deaths, 40 occurred outside of skateparks.


If a force of 20 newtons causes a skateboard to accelerate at a rate of 10 meters per second per second what is the mass of the skateboard?

F = M A20 = 10 MM = 20/10 = 2 kilograms