answersLogoWhite

0


Best Answer

All you have to do to put the shock absorber on a tennis racket is to fasten the absorber between the two middle strings at the bottom of the racket head. Place one slit into the left string and the other slit into the right string and push it up until it starts to hit the horizontal string.

User Avatar

Wiki User

9y ago
This answer is:
User Avatar
Study guides

Sports

15 cards

What happens if carbon dioxide levels in the blood are too low

Which sport combined the games of handball and squash

What type of surface is the All-England championships at Wimbledon played on

Which of these sports features a competition known as the Grand Slam

➡️
See all cards
4.14
7 Reviews

Add your answer:

Earn +20 pts
Q: How do you put a shock absorber on a tennis racket?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Where are you allowed to put a shock absorber on a tennis racquet?

ITF dictates use of shock absorber in a tennis racket. It can only be placed below the bottom cross string or above the top cross string.


What do you put on your tennis racket?

You would put on a shock absorber, or a vibration dampener, on your racket. It's a rubber placed on the bottom of your racket to reduce vibration. Also, for the grip, well, you can put an overgrip. As for the frame, you'd put paint and those plastic things at the end to keep it from getting scratched.


How do you put shock absorber on tennis racquet?

To put a shock absorber on a tennis racquet, you need to separate the two strings you want to put it in between, get one side of the absorber in there, and then use your strength to get the other side to go into the other string. It takes patience, and sometimes a little bit of time if you are not very good at it.


What is the function of shock absorber?

the function of shock absorber is to prevent the coil spring or the spring bar to move freely or to prevent them to bounce as it is.that is why they put shock absorber to have a good riding comfort depends on the road condition


What it means to put jack under axel adjacent to left shock absorber?

Under the axel (rod for steering), NEXT to the shock absorber (spring for suspension)


Why do you put a grip on your tennis racket?

So that is does not slip out of your hand.


What is the function of absorber?

the function of shock absorber is to prevent the coil spring or the spring bar to move freely or to prevent them to bounce as it is.that is why they put shock absorber to have a good riding comfort depends on the road condition


How long should your tennis racket be?

hold the grip. if the tennis racket touches the flour just then it is perfect. if its too short then you wont be able to touch the floor when you put it beside you.


How do put on a tennis racket grip?

Follow the link to Tennis Warehouse below, it has a step-by-step tutorial and also has a video.


Can you put a front gas shock absorber and a rear oil shock absorber on your car?

The front and rear axle of the vehicle works independently. Unless you have different type of absorber for left and right side, if not, there will not be any harm using either gas or hydraulic on different axle. Tks


How do you put strings on a tennis racket?

To string a racquet, you will need to purchase a string machine which can be found at most tennis site, or you could bring it to your local tennis store and ask if they string racquets. They usually charge around $20.00 per racquet.


How do you replace the rear shocks on a Ford Windstar?

To remove rear shocks:# Raise and support the vehicle and remove the wheels# Put a jack under the rear axle and raise it slightly to take the tension off the shock# Remove the lower shock absorber bolt/nut and disconnect the shock from the rear axle.# Remove the upper shock absorber-to-chassis bolt to release the shock from the vehicleTo install rear shocks: # Attach the shock absorber to the upper mounting bracket and install a new retaining bolt/nut.# Using the jack you put under the axle, slowly raise the axle while guiding the shock into the lower mounting bracket.# Install a new retaining bolt/nut and tighten to 50-68 ft. lbs.Don't forget to put the wheels back on...----Your Windstar may not have shocks. Please verify. My Windstar has a X look in the back with coil springs and thus no shocks because that is handled by the X.